Heli-max HMXE0250 User Manual

READ THROUGH THIS INSTRUCTION MANUALFIRST. IT CONTAINS IMPORTANT INSTRUCTIONSAND WARNINGS CONCERNING THE ASSEMBLYAND USE OF THIS MODEL.HMXZ7013 for HM

❏ 2. Remove the set screws from the flybar arms and align thehole with the flat spot on the flybar. Apply a small amount ofthread locker to each of th

11❏ 8. Check the two linkages and verify they are 42mm. Installthe two linkages onto the flybar control arm and the washoutarm as shown above.Temporar

❏ 3. Install three 3mm nylon lock nuts on the back side ofthe gearbox where you just inserted the 3mm screws.Tighten the bolts.TAIL BLADESBag 5-1 Cont

13❏ 2. Install the horizontal fin clamp. Using two 3x16mm self-tapping screws, attach the horizontal fin to the clamp. Do notcompletely tighten bolts

LANDING GEARBag 6 Contents: 3x20mm SHCS (4), Plastic Spacers, 3mm Nylon Lock Nut (4), 3x4mm Set Screws (4)❏ 1. Insert a 3x20mm SHCS through the unders

15❏ 2. Thread the plastic tail rotor pushrod coupler onto theshort pushrod at least 1/4" [6.4mm]. If you find the couplerdifficult to thread on y

❏ 4. The collective and throttle servos are mounted on theinside of the frame. Slide the throttle servo into the frame asshown above. Install a 2.6x10

17RECEIVER ANTENNA❏ 1. Slide the antenna tube into the mounts on the bottom ofthe landing gear. Cut two pieces of fuel tubing 1/4" [6.4mm]long an

FUTABA: 6EXH – 7CH – 9CHThis manual assumes you have already read through yourtransmitter operating instructions and are familiar with itsoperation. T

19❏ 2. Futaba T7CH: Select the [PARAMETER] menu andverify the model [TYPE>] is set to [H-1]. Position the cursoron [RESET>EXECUTE]. Press the ro

2INTRODUCTION ...2SAFETY PRECAUTIONS ...3DECIS

6EXH7CH9CH❏ Futaba T6EXH: Press the (MODE) button until the screenshows [D/R ch1 100%]. Press the (Select) button until thescreen shows [EXPO CH1 + –

21END POINT ADJUSTMENTS6EXH7CH9CH❏ Futaba T6EXH: Select the [EPA] menu and set CH1 andCH2 to 110% (left/right and forward/aft).❏ Futaba T7CH: Select t

❏ Futaba T7CH: Select the [GYRO] menu. Enable thefunction and set the switch to [SW-E] (Flight Condition Switch).Set all positions to [A 60%] which is

23PITCH CURVE6EXH7CH9CH❏ Futaba T6EXH: Select the [N-PI] menu. Set Point #1 to45%. Press (Select) to move to Point #2 and set it to 55%.Continue to se

SERVO SETUP AND LINKAGESMost servo arms have an odd number of splines, whichallows you to rotate it 90°, 180° or 270° to help with thecentering. All s

25❏ 3. Install the servo arm and screw as shown above. Locatethe left/right cyclic linkages and make sure they are both148mm long. Install the linkage

THROTTLE SETUP❏ 1. Make sure that the transmitter and receiver are “ON”and the sticks are centered. Put a servo arm in place, makingsure that one side

27GY401 GYRO SETUPIf you are using a digital servo such as the Futaba S9254 orS9253, the DS mode switch should be “ON”. Otherwise, setit to “OFF”. The

❏ 3. Once you have verified everything fits properly, mix upsome 30-minute epoxy and apply it to the exposed wood onthe root of the blade. Install the

❏ 5. Position the second blade on the tray, with the mark atthe center. Add balancing or electrical tape to the lighter enduntil the bubble indicates

3For any helicopter to perform to its full potential, it must beequipped with all the right gear (servos, batteries, receiver, etc).While other brands

❏ 2. Turn on the transmitter and receiver. Move the collectivestick to full throttle. Place the pitch gauge on the blade asshown and set it to +10°. A

31❏ 2. Trim the front of the body as shown above. Make a cleancut by making several passes with a hobby knife. Mark thebody 5/8" [16mm] up from t

CHECK THE CONTROL DIRECTIONSTurn on the transmitter and allow the gyro 5 seconds toinitialize before moving the helicopter or operating the sticks. If

33❏ When the left (collective) stick is pushed forward, theswashplate should move up and the carburetor should open.Descend Collective❏ When the left

RANGE CHECKGround check the range of your radio before the first flight ofthe day. With the transmitter antenna collapsed and thereceiver and transmit

35Please try to find a local club (check www.modelaircraft.org forlistings) or find an experienced modeler for help before startingto fly. There are a

Descend CollectiveWhen the left (collective) stick is moved downward, thehelicopter will descend.Left Tail RotorWhen the left (tail rotor) stick is mo

37ADJUST BLADE TRACKINGIf you feel uncomfortable adjusting blade tracking by yourself,please have a helper do the sighting for you and simply fly them

continues to fly inverted, you will need to start adding innegative (–) collective (or pull the collective stick backtowards you) to maintain altitude

39Stock # Description ContentsHMXE1008 ...Main Rotor Blades 600mm...25 x1pcHMXE4463 ...Metal Swashplate Set...134 x1pc,

4Remember: Take your time and follow the instructionsto build a safe and enjoyable model.This is a partial list of items required to finish the Kineti

Stock # Description ContentsHMXE4400 ...Hex Adapter...61 x1pc, M x2pcsHMXE4401 ...Start Shaft ...62,63,68,143,157,M x2pcsH

Stock # Description ContentsHMXE4705 ...Assorted HardwareHMXE7292 ...Ball Bearing (3x10x4mm) ...162 x4pcsHMXE7294 ...Tail Slider BB (6x10

Stock # Description ContentsHMXE4450 ...Cooling Fan ...113,114 x1pcHMXE4451 ...Clutch Bell ...

Stock # Description ContentsHMXE4462 ...Plastic Links...See BelowHMXE4469 ...Stainless Ball 3mm Short ...206

™From smooth and stableFrom smooth and stableto extreme maneuvers!to extreme maneuvers!From smooth and stableFrom smooth and stableto extreme maneuver

5• There are two types of threaded fasteners used in this kit:Self-Tapping Screws are designated by a diameter anda length and are intended to thread

6LOWER FRAME AND TANKBag 10 Contents: Main Frame Assembly (Engine Mountand Fuel Tank Installed), Fuel Stopper, Brass Tubing,Silicone Fuel Line, and St

7Note: You will need to lock the crankshaft while tighteningthe clutch and nut. We recommend using a O.S. CrankshaftClamp .32-.46 (OSMR1004) as shown

❏ 6. Install the engine onto the mount using thread lockerand the four 3x16mm screws provided.❏ 7. Install the right side frame using the 3x12mm screw

9❏ 3. Apply thread locker to one 3x12mm socket head capscrew. Install the screw and washer as shown above.Repeat on the opposite side of the frame.❏ 4